Tutorial--The "Knotted" Cowl (with added Instructions)

Friday, November 18, 2011

A funny thing happened on the way to making my newest "hide the neck scars" Cowl tunic....I scooped the neckline way too low!  Uh-oh!  I had to think of a way to "fill it up" with the collar, because I didn't have enough fabric to cut another front. In fact, by the time I discovered that the neckline was too low, almost the entire garment was sewn...sigh :( 
Luckily,  I remembered a cowl variation that I used to teach years ago, when my family owned a fabric store...The "Knotted" Cowl.

Here is a close-up of the collar--

What looks like a "knot" at Center Front is actually a manipulated pleat, and here is how it's done....

(click on any photo to enlarge it)

From the wrong side of the garment, I located the CF of the cowl collar by folding the tunic in half. Then as shown below, I stitched a 2-inch deep pleat from the top edge of the collar (through all thicknesses) , stopping about 2" from the neckline seam. Leaving that last 2" of the pleat unsewn will mean something later on in the process--

Next, I made a quick trip to my ironing surface and gently pressed the pleat flat...yes, making a simple box pleat :)  And that is just about all there is to it!  
Except for some very simple folding. Below is the tunic on my form, right sides out (photo lightened for clarity). 
The Cowl Collar has been folded down one time, all the way around. You can clearly see the box pleat that was made. The pin that you see is only there so I could photograph this first fold....  

...because, without the pin holding the first fold of the collar up, the weight of the pleat almost "automagically" makes the Cowl Collar fold itself again at CF...giving the illusion of a "knot" as shown below--

Now, with just a little bit of tucking-under of the CF  into the "dimple" (made when the bottom part of the pleat was left unsewn), there it is...a "knot" that's not a knot !

What follow is a series of photos to make the folding/tucking part of this design more clear--    All of the photos below can be Clicked to enlarge them.

First of all, remember that the pin is ONLY here to hold up the first fold-down of the cowl collar, so that I can show what comes next...it has NO other purpose.  When you make yours, you will not need that pin at all...it serves No construction purpose...I ONLY needed to put it there to show you what comes next.

OK...the red circle in the photo above shows the "Hollow"  or "Deep Dimple-like Hole"  that was made by leaving the last 2" of the pleat NOT sewn (as demonstrated  in the series of photos of the original tutorial).  When you look closely at the photo above, you can "little fold edges" that show where the "Hollow/Dimple/Hole" is located.

 Now....to form the "False Knot", One Last Fold or it could be called a "Tuck and Roll-Under" needs to be made.... --click photo below to enlarge--   (Notice that the pin is NOT there now).

As shown ABOVE by my crudely drawn arrows (sorry..best I could do).....So, as shown by those arrows, the LAST steps are to TURN and ROLL the edge of the collar UNDER ITSELF all the way arround, and THEN use the "DIMPLE/HOLLOW/HOLE" to hold the "Roll" in place, by "tucking-in/pushing" it  INTO that 2-inch  "DIMPLE/HOLLOW/HOLE" (shown above by the 2 double curved arrows at the center front).   
After the collar is "folded/tuck-rolled" under itself, and pushed into that "hole" at CF shown by the double curved arrows....it will look like this--

You can play with and arrange the folds of the collar that surround the Rolled-Under "Pleat That Now Looks Like a Knot" that has been tucked into the CF "Hole/Hollow/Dimple"...anyway you want to.   Just make sure that the (pleated) Center Front of the COLLAR has been ROLLED UNDER ITSELF and Tucked-into the CF "hollow-dimple"

I hope that helps those who did not understand my first set of Tutorial instructions...I cannot think of any other ways to make this more clear than these extra instructions.   Thanks so much for visiting my Blog.

SEWING NOTES--  Fabric is a poly/lycra knit from Gorgeous Fabrics (purchased quite a while ago). Shoulder Seams and Hems are stabilized with poly/lycra Pro-Tricot Fusible Interfacing from Fashion Sewing Supply.